The following photographs describe some of the USED EQUIPMENT that CCS has in our large inventory. Much of the equipment is still on the mill floor and can be test run prior to purchasing. All of the USED EQUIPMENT can be inspected upon request. The equipment can also be reconditioned and modified to meet the buyers needs. All USED EQUIPMENT is subject to prior sale without notice. Please contact us for more information.

Complete Low Melt Bonding Line

1 - Used "as is" Low Melt Bonding line complete with five 36" wide weigh pan blending hoppers, bale extensions, blend conveyor, blender, Low Melt pre opening, recycle system, distributor, suction fan, 60" wide garnett feeder, shaker chute, double section double doffer garnett, safety cage, 60" wide x 120" lay down cross lapper, floor apron, Perpetual Machine Company single pass oven, cooling section, compression slitter, hot wire cut off, surface wind up, and electrical controls.

Price: TBD

Terms: Net cash prior to shipment

Delivery: 2 to 4 weeks from receipt of deposit

F.O.B. Point of shipment

Voltage: 480 - 3 - 60

Photos: Available upon request

VIDEO
Please click the link below to watch a video of the above Low Melt Bonding Line in production.

Used Low Melt Bonding Line Video

1998 Wise LOFT PLUS Fiber Blowing System

1 - Used "as is - where is" Wise LOFT PLUS System I double nozzle fiber blowing system complete with WK-4 Feed Hopper, VWO-42 Vertical Fine Opener, dual 100% Shut Off Valves, dual Stuffing Fans, dual Foot Switch controls and Control Panel. Unit is complete and in good operating condition. Control Panel will be built with all new materials.

Price: $32,500.00 usd

Terms: 50% deposit - balance due prior to shipment

Delivery: 1 to 2 weeks from receipt of deposit

F.O.B.: Point of shipment

Location: Charlotte, NC

Voltage: 220/440V 3Ph 60Hz

YOM: 1998

Production Rate: 600 to 800 pounds per hour

Used equipment is subject to prior sale without notice.

Complete Nonwoven Thermal Bonding Line

Used "as is - where is" Wise/Hergeth Nonwoven Thermal Bonding line complete with the following equipment:

1 - Wise 36" wide low melt pre-opening system

1 - Wise 36" wide waste re-run system

1 - Wise (5) hopper weigh pan blend line complete with 36" wide extended aprons, load cell weighing feeder, Hergeth blend conveyor, Hergeth Blender, outlet transition, hump magnet, and related fans

1 - Hergeth 60" wide fine opener with air box, chute feed, vertical course opener, hump magnet, and related fans

1 - Hergeth 60" wide reserve system complete with air box, chute feed, pin opener, hump magnet, and related fans

1 - Hergeth 2.5 meter air box, chute feed, Master Card machine, 2.5 meter x 130" lapper, and hanging floor apron

1 - Hergeth 130" wide four zone inline drafting machine

1 - Dalton Sheet Metal 130" wide bonding oven with cooling zone

1 - Wise 130" wide three head compression slitter, hot wire cut off, level control, and two roll surface winder

1 - Wise blend line electronic weigh control system

1 - Wise blend line motor control center with operator start stop station

1 - Hergeth card line motor control center

1 - Hergeth card line operator start stop station

1 - DMS oven and cooling zone motor control center with operator start stop station

1 - Wise finish end motor control center with operator start stop station

1 - Set of miscellaneous spare parts

Price: TBA

Terms: 50% deposit - 50% prior to shipment

F.O.B.: Point of shipment

YOM: 1989

Voltage: 480V 3Ph 60Hz

Location: Charlotte, NC

Note: Used equipment is subject to prior sale without notice. Removal cost is not included in purchase price.

Note: Additional photos and equipment specification available upon request.

Used Needle Punch Line

1 - Complete Used "as is - where is" Needle Punch Line including the following:

BLEND LINE
3 Fiber Controls Weigh Pan Hoppers with Sargent Combs
Fiber Controls Blend Conveyor
Fiber Controls B-1 Blender
Fiber Controls Hump Magnet
Rotary Drum Condenser
IR Edge Trim Opener with Silo
Ductwork

WEB FORMING
D & F Volumetric Card Feed Hopper
Wise Shaker Chute
D & F 60" Double Cylinder, Double Lickerin, Single Doffer Compact Card with Metal Detection and D-B Comb
Buffalo Batt 100" Horizontal Cross Lapper
Buffalo Batt Floor Apron 174" wide
P & S 790 Pre-Needler with Entrance Feed Conveyor and Batt Feed Rolls (1970)
Fehrer NL21 Needleloom, 164" with 3.5" stroke (1972)
Inspection Station
Slitter with 7 Air Cutting Knives
Automatic Rotary Cross Cutter with Counter
Two Roll Surface Wind Up

VIDEO
Please click the link below to watch a video of the above Needle Punch Line in production.

Used Needle Punch Line Video

PICTURES

    

   

   

   

   

   

   

   

   

   

   

   

   

   

   

   

 

		.